Anyone up for going to the Providence Auto Show? The 2015 Mustang will be on display there. It is running this Fri thru Sun.
( Feb 7 thru Feb 9 )
Anyone up for going to the Providence Auto Show? The 2015 Mustang will be on display there. It is running this Fri thru Sun.
( Feb 7 thru Feb 9 )
Didn't even know anything about it. Unfortunately, i have plans.
SVT COBRA
I might be up for it; maybe head down after breakfast on Saturday????
2003 Cobra "Terminator" Convertible
Last Dyno Run = 496 rear wheel hp, 490 foot pound of torque
Bob, when are you thinking of going. Jay and myself may be interested.
http://www.motortrendautoshows.com/providence
Bruce
TFS TW heads, rockers, 75mm intake, cam, 75mm TB, CAI, MAF, DeatschWerks 35# injectors, Aeromotive rails/regulator, 255 pump, BeCool rad, alum water pump, MSD 6A/coil, alum flywheel, PP, driveshaft, McLeod clutch, Torsen T2R, 3.73, 31spline axles, 17" 95 Cobra R, NT-05 255/275, MM CC plates, coil-over (Bilstein), rlca, K-brace, A-arms, SF conns, Cobra brakes, =len shorties, 2.5" SS Hpipe, Borla CB...
Going snowmobiling, for the first time in over a month. Bring on the snow !!!
had no idea this show even exsisted.....thanks for sharing
-- Ian --
2003 10th Aniv. Cobra Convertible Torch Red
Born on 6/18/2003 / Build # 4357 / # 489 0f 10th Aniv
1 of 369 Torch Red 10th Aniversary cars Built
This Sat after breakfast sounds good to me.
A bit more information:
http://www.valleybreeze.com/2014-02-...idence-weekend
I was beginning to wonder - I couldn't find anything that said the 2015 Mustang would be there. Then I found this (you have to scroll down a ways to find it):
https://www.facebook.com/NEAutoShow
Yeah, I actually found something useful on Facebook - I guess there's a first for everything.
I think we're in for this.
Bruce
TFS TW heads, rockers, 75mm intake, cam, 75mm TB, CAI, MAF, DeatschWerks 35# injectors, Aeromotive rails/regulator, 255 pump, BeCool rad, alum water pump, MSD 6A/coil, alum flywheel, PP, driveshaft, McLeod clutch, Torsen T2R, 3.73, 31spline axles, 17" 95 Cobra R, NT-05 255/275, MM CC plates, coil-over (Bilstein), rlca, K-brace, A-arms, SF conns, Cobra brakes, =len shorties, 2.5" SS Hpipe, Borla CB...
Bob C., Jay and myself went to the show Saturday to see the 2015. Here are some pics I took, though I doubt you will see anything you haven't already seen in the official pics. My impressions didn't change a lot. I disliked the nose and headlights as much as ever, but the rest of the car was definitely nicer and made a better impression than before. I still don't like that the fender line and the styling line are one and the same and are generally flat with no rake to it. The tails/rear end looked better than my previous impressions and did the side view.
On another note, the new Camaro and Vette also have nicer rears than previously. They ditched those awful tail lights both had and replaced the two cut off circles on each side with one rectangular light on each side. It's amazing how much that little change makes both cars look so much better!
Last edited by ToplessPony94; 02-09-2014 at 02:19 PM.
Bruce
TFS TW heads, rockers, 75mm intake, cam, 75mm TB, CAI, MAF, DeatschWerks 35# injectors, Aeromotive rails/regulator, 255 pump, BeCool rad, alum water pump, MSD 6A/coil, alum flywheel, PP, driveshaft, McLeod clutch, Torsen T2R, 3.73, 31spline axles, 17" 95 Cobra R, NT-05 255/275, MM CC plates, coil-over (Bilstein), rlca, K-brace, A-arms, SF conns, Cobra brakes, =len shorties, 2.5" SS Hpipe, Borla CB...